EM4095 RFID PDF

EM4095 RFID PDF

The RFid Reader Board is a kHz RF transmitter and reciever, featuring the EM controller chip. The reader has three main functions. The EM is replacement IC of the UB Atmel reader chip. EM is a CMOS integrated transceiver circuit for RFID applications. EM Read only Receiver and transmit to UART 10 digit hexa code by ASCII.

Author: Tygomuro Dok
Country: Haiti
Language: English (Spanish)
Genre: Music
Published (Last): 25 June 2011
Pages: 235
PDF File Size: 7.82 Mb
ePub File Size: 12.17 Mb
ISBN: 314-1-46217-597-8
Downloads: 41996
Price: Free* [*Free Regsitration Required]
Uploader: Kazragul

Digital multimeter appears to have measured voltages lower than expected. Dec 248: Measuring air gap of a magnetic core for home-wound inductors and flyback transformer 7. After that, I just test out the antenna with a simple range test.

Then, I just depend on the simulation software to optimize the value of the R,C, L so that I get the best S11 at my freq, This will prevent where a bit generator could be used to generate all possible codes.

Magnetic RFID reader antenna 1. Best regards, Dusan Mihajlovic. So far what i did is i import the layout structure of the PCB and simulate the S11 of the antenna. I am doing a project on Asset tracking system using active rfid. So please reply me the embedded c code urgently.

How can the power consumption for computing be reduced for energy harvesting? The Interface to the EM is through 4 lines.

  LAKO JE SMRSATI PDF

The other hack would be to listen with a long range KHz antenna, and recording all bits. Equating complex number interms of em495 other 6.

RFID Reader/Transmitter Board, kHz, EM, IDC

Can you point me to some literature and calculation tool for building loop PCB antenna. Connect a serial cable to X6 and press F4 to program. ModelSim – How rvid force em40995 struct type written in SystemVerilog?

Now the program will start and show some info on the LCD. Connect the battery and measure with a Volt meter if IC1 actual outputs 5V.

This will result in a higher distance that you can use for the tags. Part and Inventory Search. CMOS Technology file 1.

Choosing IC with EN signal 2. The time now is IC4 is a serial interface buffer so we can connect the PCB to our computer for logging and programming.

Catalog | EM Microelectronic

Connect the antenna to connector X2. The black rfidd must match the line on the PCB Kathode. Equating complex number interms of the other 6. PNP transistor not working 2. Dec 248: For normal operation SHD is set Low. Heat sinks, Part 2: The time now is The antenna coil inductance L and capacitor Cres is a tuned circuit set to resonate at kHz.

AF modulator in Transmitter what is the A? AF modulator in Transmitter what is the A? M3x6 bolt and nut. As it was suggested – the EM simulation soft can do that.

  GEOMETRY ALEXANDER KOEBERLEIN PDF

EM4095 rfid 125khz rfid reader module

PNP transistor not working 2. I don’t know feasibility of this solution as you need many turns due to higher inductance for KHz. The PCB is now ready for use. Now solder the remaining pins. With only a few external components the EM can generate the kHz resonant magnetic field required for reading and writing em44095 magnetically coupled RFID Transponders. But since the used SMD chip is relatively large there should not be any problem.

Make sure there are no solder drops on the PCB. The PIC16FA may not offer system clock frequency me4095 enough to sufficiently service the interrupt routine. When a valid tag is held in front of the antenna, it will activate the relay for 2 seconds. The red wire is the plus. Further to that the digital processor can then take appropriate actions based on the data stored on the Transponder.

Use an iron with a small tip. A long range scanner would be very hard to make.