DIN 8593-5 PDF

DIN 8593-5 PDF

Standards. DIN Manufacturing processes joining – Part 5: Joining by forming processes; Classification, subdivision, terms and definitions. Title ( German). DIN references following documents: DIN , , Manufacturing processes joining – Part 5: Joining by forming processes; Classification. Find the most up-to-date version of DIN at Engineering

Author: Gumi Yorn
Country: Armenia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 28 August 2008
Pages: 152
PDF File Size: 5.83 Mb
ePub File Size: 7.23 Mb
ISBN: 566-5-91282-326-1
Downloads: 92138
Price: Free* [*Free Regsitration Required]
Uploader: Tekazahn

Specimen width is 45 mm, overlap of the sheets is 35 mm and length of the single sheets is at least mm. Rectangular joints are to be located perpendicular to the load direction. These bulges are used to clamp a joining partner e. It must 853-5 ensured that the joints are not stressed when the sheets are bent e. The resulting clinched joints are also referred to as joints in the following.

Page 15 VW Page 16 VW The minimum break force Fmin depends on the sheet thickness combination, the strength 8539-5 the raw material and the type of joint and must be specified in the drawing.

Joining by forming processes; Classification, subdivision, terms and definitions Clinchen -? Mechanical joining ; Tube forming ; Upset bulging. Drawing version desired values of the joint: The joints were sin for the three combinations of the DC01 steel and EN AW- aluminium alloy sheets with the thickness of 2mm.

Especially for round joints, care must be taken that the joint 8593–5 not fall apart when preparing the microsections. No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group. This is a preview of subscription content, log in to check access.

  GLI SPIRITI NON DIMENTICANO PDF

Joining by Upset Bulging

Here, at least the ratios specified in Table 6 must be achieved: The article presents the analysis of the structure of the load capacity of riveted joints. Considerably lower strength is to be expected if this is not the case. In the case of the conventional riveted joints the maximum load capacity of the joint is determined by the strength of the fastener. Page 17 VW If undercut is present on both sides: Here, it must be ensured that the measured values are not affected by the preparation work.

The result Fmin Ftransverse — 2 sigma is a reference value for the drawing specification. The English translation is believed to be accurate. Their properties must match to the cases to be tested. J Mater Don Technol 5: From all sheets and rivet specimens arrangements the highest load capacity of the joint was obtained for the DC01 sheet material joints, and the lowest load capacity of the joint was obtained for the EN AW sheet material joints. An axial compression load is usually applied to a rotation-symmetric workpiece e.

VW _2_TOX铆接_图文_百度文库

If this is not the case, don joint is NOK. Joining by Upset Bulging. Such processes are necessary to fulfill the growing demands on industrial production of multi-material joints and general lightweight production.

In particular, conventional fusion welding processes reach their limits due to high heat input Nahtlose kaltgezogene Rohre; [Precision steel tubes — technical delivery conditions — part 1: The overall thickness of the joining partners must not exceed 5 mm. J Clean Prod 19 6—7: If the material flow in the structure is uninterrupted, as can be seen in the Figure on the left, it is a wrinkle. Beuth, Berlin Google Scholar. Page 13 VW Release testing process qualification A total of 10 specimens according to Section 3.

  DRAWING ESSENTIALS DEBORAH ROCKMAN PDF

Standards with the titles given in German are either only available in German or may be procured in other languages from the institution issuing the standard. For the four joining systems the lap joint specimens were made and tested in the shearing test. Introduction Joining by upset bulging is a mechanical joining process, which is commonly used to create joints with a form and force fit between tubes and other structures, such as sheets, 85935- tubes, or profiles.

Undercut f not present on both sides: 85993-5 sheets with different plasticity characteristics, the harder sheet is to be arranged on the side of the punch wherever possible “hard in soft”. The strength of the SSPR joint is determined by the mechanical properties of the material of the joined sheets.

J Manuf Process 15 1: Air and Exhaust manage General information — — Part xin. If the base is cracked, check for microsection preparation errors. EN,Eurocode 3, Design of steel structures, Part This electronically generated standard is authentic and valid without signature. The assessment criteria according to Section 3. In the latter case, the microsection must be prepared so that the microsection plane is located in the center of dib clinched joint for the determination of the geometric characteristics.

The connection is a positive locking and friction locking joint. Living reference work entry First Online: