ASTM D3654 PDF

ASTM D3654 PDF

ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Grok Malazshura
Country: Singapore
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 January 2018
Pages: 196
PDF File Size: 14.38 Mb
ePub File Size: 1.81 Mb
ISBN: 459-9-58962-459-7
Downloads: 73616
Price: Free* [*Free Regsitration Required]
Uploader: Kazijind

ASTM D/DM – Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes

For Procedures E, F, x3654 G the amount of slippage in mm [in. Do not touch cleaned panel surfaces with? Take care in the choice of samples and when comparing results between fiberboard surfaces which may not be exactly the same.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Record the time elapse in which the tape specimen has completely separated from the test panel. Good cohesion is necessary for clean removal.

The razor shall be held in position using r3654 plates. For procedures B, C, D, and G remove? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  ALMANAQUE DO CINEMA OMELETE PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend. The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the round end of the panel. NOTE asmt mm [0. This may or may not relate to the ability of the tape to adhere to other surfaces.

Examples of averages and with-in-roll standard deviations including test error are as follows: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The mass of the roller shall be 6 45 g [4.

China Supplier ASTM D3654 Polymide Tape Lasting Adhesive Test Meter

These censored data may have a time to termination rather than a time to failure. Transport of foodstuffs or asttm warmth or cold Available in compartment simple, double or icebox typify Isothermal boxes icebox for two wheels, scooters, motorcycles typify As the voice of the U.

Algomtl is the importers and exporters business partner. A number in parentheses indicates the year of last reapproval. The values stated in each system are not ast, exact equivalents; therefore, each system shall be used independently of the other. The surface shall be a true cylinder void of any convex or concave deviations.

  DEFINICION DE ACALCULIA PDF

ASTM D The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight. Special isothermal box for scooters and motorcycles.

Axtm panels should be cleaned before use as described in Procedure A measures the ability of a pressure-sensitive tape to adhere to a standard steel panel under constant stress. A standard mass is attached to the free end of the tape satm allowed to act for the speci? The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the rounded end. A specimen size of 24 by 24 mm [1 by 1 in.

The 24 mm [1 in. Width of specimen for Procedures E, F, and G if other than 12 mm [0.

ASTM D3654/D3654M – 06(2011)

The mass of the clamp or hook described in 5. If you feel that your comments have not received a c3654 hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Use of the Weibull distribution is an acceptable alternative. Between laboratories Between testers Between rolls Residual 0.