ASTM A513 PDF

ASTM A513 PDF

Learn about ASTM A steel mechanical tubing and Atlas Tube’s manufacturing capabilities regarding this product for OEM applications. CALIFORNIA. Arrow Route. Rancho Cucamonga, CA WWW. ASTM A TUBING SPECIFICATIONS. TOLERANCES. ASTM A/AM: Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing.

Author: Kajir Digrel
Country: Italy
Language: English (Spanish)
Genre: History
Published (Last): 1 June 2012
Pages: 357
PDF File Size: 13.68 Mb
ePub File Size: 4.59 Mb
ISBN: 133-2-90414-764-5
Downloads: 5650
Price: Free* [*Free Regsitration Required]
Uploader: Shakakus

If no grade is speci?

A Square Carbon Steel Tube | Alro Steel

B Up to and incl 11? For grades of round tubing not shown in Table S5. Such defects as seams, slivers, pits, laps, etc. B,C Outside Diameter, in. For lengths under 1 ft satm straightness tolerance shall be agreed upon between the purchaser and producer. NOTE S1—A lot shall consist of all tubes, before cutting to length, of the same size and wall thickness which are produced from the same heat of steel and, when heat treated, subjected to the same?

A5133 Tubing Wall thickness 34 Outside Diameter, in. Materials and Manufacture 4. A,B Outside Diameter, in. The area producing the signal may be examined. Since the sections are special, dies and other tools are not held available.

A513 Square Carbon Steel Tube

Both retests for the elements in question shall meet the requirements of the speci? Tubing heavier than 16 gage will normally be shipped loose, bundled, or in secured lifts. D No Flash tubing is further processed by DOM for closer tolerances, produced to outside diameter and wall, inside diameter and wall, or outside diameter and inside diameter, with no dimensional indication of inside diameter?

  JIS G3313 STANDARD PDF

Committee A01 has identi? The squareness of sides is commonly determined by one of the following awtm.

Special packaging requiring extra operations other than those normally used by a producer must be speci? A Wall Thickness in. Approved May 1, 1 Revised 5.

These requirements shall not be considered, unless speci? Up to 3, incl Over 3 to 43? Nondestructive Electric Test S8. Type 1a, as-welded from hot-rolled steel with mill scale ; Type 1b, as-welded from hot-rolled pickled and oiled steel mill scale removed ; Type 2, as-welded from cold-rolled steel; Type 3, sink-drawn hot-rolled steel; Type 4, sink-drawn cold-rolled steel; Type 5, drawn over a mandrel; and Type 6, special smooth inside diameter.

It is the intent of this test to reject tubes containing injurious defects. Wall Thickness Outside Diameter Range, in. D Flash Controlled to 0.

A513 Type 1 & 2 Tubing

The purchaser may specify in the order a speci? Outside diameter 3 tolerances for cold-rolled steel tubing, sink drawn and DOM, are shown in Table 5. The outside corners may be slightly?

Said notch shall have a depth not exceeding ? Link to Active This link will always route to the current Active version of the standard. Product analysis, except for rimmed or capped steel, is to be in accordance with usual practice as shown in Table 3.

Evidence of lamination or burnt material shall not develop during the? C These radius tolerances apply to grades of steel covered in Table 1. For particular applications, properties may be adjusted by negotiation between purchaser and producer.

Approved December 1, 1 Revised Table 2 to agree with composition requirements contained in Speci? B Where the ellipsis Flash-In-Tubing is produced to outside diameter tolerances and wall thickness tolerances only, and the height of the inside welding? Types and Conditions This standard has been approved for use by agencies of the Department of Defense.

  BULA DIPIRONA INJETAVEL PDF

Within the text the SI units are shown in brackets. If the order speci? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. When an oxide-free surface is speci? Permissible Variations in Dimensions for Round Tubing 8. Side leg of square to be equal to tube diameter except minimum length of 1 in. This condition is available in Types 1a, 1b, 2, 3, and 4. For each additional 10 ft or fraction thereof over 24 ft, an additional allowance should be made of plus or minus 1?

Therefore, when inquiring for shapes other than square and rectangular, it is essential to give full details as to dimensions and?

A — 07 Standard Speci? These special sections may be made through turkshead rolls or through a die with or without use of a mandrel. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Manufacturing practices limit the size range and section available from the various producers. Cleanup by Centerless Grinding S2.